What is Type N Mortar?

Type N is a medium-strength masonry mortar (ASTM C270) compounded for general above-grade exterior masonry on residential structures. It uses a 1:1:6 ratio of portland cement, hydrated lime, and clean masonry sand, yielding 750 PSI minimum compressive strength. The high lime content gives Type N excellent workability, autogenous-healing capability for hairline cracks, and a softer profile that flexes with thermal cycling. For most DFW chimney veneer above the roofline, Type N is the correct call — it is soft enough to crack before the stone does (sacrificing the joint, not the stone) and bonds well with limestone, brick, and most natural veneers.

Properties Reference

| Property | Value |

| — | — |

| Compressive strength | 750 PSI minimum (ASTM C270) |

| Density | 120-130 lb/ft3 |

| Freeze-thaw rating | Good |

| Fire rating | Non-combustible |

| Typical DFW cost | $0.45-$0.75/lb; $4-$-+ per linear foot of joint |

Where We Use Type N Mortar in DFW

Type N Mortar shows up in the following applications across DFW fireplaces and chimneys: Above-grade chimney veneer, fireplace surround stone, exterior masonry repointing. The right application is driven by where the material sits in the assembly. A material that performs beautifully on an interior surround can fail aggressively on a chimney crown, and the reverse is also true. The DFW climate adds a layer that most national specification guides do not account for: the Blackland Prairie clay subsoil swells roughly 30% with water content, which puts cyclical mechanical stress on chimney foundations, and we run 25-35 freeze-thaw cycles per year with a stack of 5-8 hail events on top.

When we evaluate Type N Mortar for a specific project, the questions we work through are the assembly position (interior surround vs exterior veneer vs crown), the substrate (firebox brick vs framed wall vs masonry chimney chase), the mortar or adhesive system, the load path, and the design intent. The notes below cover the most common applications, and the selection logic our team uses to decide whether Type N Mortar is the right specification for the work at hand.

Cost Ranges in DFW (2026)

Material-only ranges and typical installed pricing for Type N Mortar in DFW: $0.45-$0.75/lb; $4-$-+ per linear foot of joint. List pricing on Type N Mortar in our Plano showroom is published in the trade pricing book; Trade Pro members receive 15% off list. Designers can request a written quote with quantity discount on orders over 200 sqft. Delivery within 30 miles is included for Trade Pro orders. Out-of-area delivery is quoted per job. Showroom pickup is always free.

Pros and Cons for DFW Climate

DFW-specific note: the Blackland Prairie clay-soil cycle and the 25-35 freeze-thaw events per year are the two environmental factors that most distinguish DFW from coastal or arid Southwest markets. The June 2025 hail season alone produced an estimated $7-10 billion in insured losses across the Metroplex, and chimney crowns and caps were among the most-damaged building components. Specifying Type N Mortar with these conditions in mind is the difference between a 50-year service life and a 15-year repair cycle. Our specification process always accounts for the seasonal calendar and the underlying soil and climate dynamics.

How SFS Specifies and Installs Type N Mortar

Our standard practice on Type N Mortar is to verify the substrate and load path before any material is ordered, pull samples for owner approval before fabrication, and document every step of the install with photographs that become part of the project file. For warranty applications, the documentation file is the audit trail — and it is also the record that lets a future designer or chimney professional understand what was done and why. We adhere to NFPA 211, IRC R1003, and ASTM C270 / C199 / C315 as applicable to the assembly we are building. Where Type N Mortar is part of a firebox or smoke chamber, we follow refractory specifications without exception. Where it is exterior masonry, we use Type S mortar at crowns and Type N at vertical veneer joints unless the project specification dictates otherwise.

Frequently Asked Questions

Yes. We deliver Type N Mortar to job sites across DFW with our box-truck fleet. Trade Pro members receive complimentary delivery within 30 miles of the Plano showroom; outside that radius, delivery is quoted per job. Pickup at the showroom is always available for designers managing their own logistics.

Yes. We pull production batches that match the showroom sample within two shades, photographed under the same lighting your designer will use for the final review. We will hold a single batch for up to 14 days while the designer finalizes the spec. Trade Pro members can request extended hold windows.

Trade Pro members receive 15% off list on Type N Mortar and all in-stock materials. Membership is free for licensed designers, builders, and contractors. Application takes about 5 minutes at the showroom or by phone, and approval is typically same day.

Yes. We offer turnkey install on every material we sell. Projects are scoped by our install lead at the showroom or on site, and the estimate is firm — no change-order surprises. Install scheduling typically runs 3-5 weeks out depending on season.

Related Materials

• [Lueders Limestone](https://spacefireplaceservices.com/materials/lueders-limestone/)
• [Cordova Cream Limestone](https://spacefireplaceservices.com/materials/cordova-cream-limestone/)
• [Austin Stone](https://spacefireplaceservices.com/materials/austin-stone/)
• [Texas Ledgestone](https://spacefireplaceservices.com/materials/texas-ledgestone/)
• [Soapstone](https://spacefireplaceservices.com/materials/soapstone/)

Get a Specification Quote

Schedule a consultation for a Type N Mortar project — call ☎ 817-635-6260 or visit https://spacefireplaceservices.com/contact/. We respond to inquiries within one business day.