Skip to main content
Arlington · From $650

Electric Fireplace Installation in Arlington, TX

An electric fireplace is the easiest way to give a room a glowing focal point where no chimney exists — and the finish is everything. We install plug-in or hardwired units wall-mounted, set into an existing masonry firebox, or freestanding, and we handle the framing and trim so it sits flush and reads as built-in, not bolted-on. The flame effect becomes a genuine centerpiece on a media wall, a bedroom, or an office. Clean install, clean look, and no venting or gas to worry about. Serving Arlington (17 ZIP codes, 399k residents) and surrounding neighborhoods with same-week scheduling.

399k
Arlington residents
17
ZIP codes covered
7
Neighborhoods
CSIA
Certified techs
What is it

Electric Fireplace Installation in Arlington

Electric fireplace installation is new-unit work: we frame the opening, bring the power, and set a plug-in, wall-mount, recessed-linear, or insert electric fireplace that has never run in your home before. No flue, no gas — the whole job is carpentry and circuitry, finishing in a unit that looks built-in because it genuinely is.

Local dossier · Arlington, TX

Half the living rooms in Arlington share the same wall: floor-to-ceiling brick, a firebox in the middle, a raised hearth running the width of the room. The city grew fast after the GM plant opened in 1954 and then exploded through the 70s and 80s, so that wall shows up everywhere from ranches near Randol Mill to two-stories off Green Oaks. It's a canvas, and it's why re-faces are most of our Arlington design work — plaster, large-format tile, or a steel surround over the old brick, with the hearth kept or dropped to floor level depending on how the room wants to sit. Underneath, the story is age. Those 1980s builder fireboxes are past their service life, and replacement parts for most were discontinued years ago, so a re-face is usually the moment to set a sealed gas insert inside the old opening and vent it through a new liner. Newer homes down toward the Mansfield line are a different job — media walls, linear units, heat management for the TV above. One honest note: sometimes painting the brick is genuinely the right call, and it costs a tenth of a re-face. We'll say so when it's true. Either way, the gas work gets permitted, inspected, and photographed before we call anything finished.

AT&T Stadium

Why this matters in Arlington

Arlington's mid-century brick ranches and the newer Viridian master-planned community sit squarely between Dallas and Fort Worth. Freeze-thaw crown cracking on the older stock and prefab cap work on the newer builds are the year-round staples. From feature wall to firebox, we keep the hearth the standout it was built to be. That local stock is exactly why our Arlington crews tailor electric fireplace installation to the homes here — not a generic checklist.

Common signs in Arlington homes

  • You want fireplace ambiance with no gas, wood, or flue
  • A room addition or condo that has no chimney at all
  • An unused masonry firebox you'd like to repurpose
  • You're building a feature wall and need a recessed unit set into it. into it.

Electric Fireplace Installation in Arlington (Tarrant County) — what's local

Arlington sits in Tarrant County (county seat: Fort Worth). Fort Worth anchors a county of 2.12M residents, where hearths range from cattle-drive-era heritage masonry to modern gated builds in Westlake, giving our team the widest variety of repair scopes in DFW. For electric fireplace installation that means our Arlington crew sizes up the local housing stock before quoting — and follows Tarrant County permit requirements for any work that needs an inspection sign-off.

Climate & code file · the DFW Metroplex

DFW is home base for fireplace work done right. Dallas–Fort Worth is where Space Fireplace Services proves that the hearth is the centerpiece of the room and gets treated that way — on a Preston Hollow estate or a Frisco new-build alike. It's also where North-Texas freeze-thaw, hail, and expansive clay do the most damage to brick stacks, so the copy below is written to keep that centerpiece sound through the worst the metro throws at it.

01

Expansive clay soil

Arlington sits on Houston Black clay that can shift several inches between a wet spring and a drought summer. A rigid masonry chimney riding on moving ground develops stair-step cracking through the mortar joints at the base of the stack — the tell that the masonry is being torqued by the soil, not merely weathering. We diagnose active settlement versus stable historic movement before we quote, and we'll tell you honestly when the real cause is foundation-side and has to be addressed first.

02

Hard freezes & spalling

A North-Texas hard freeze — the sub-20°F events of recent winters — drives into brick and crown that soaked up December rain. The trapped water freezes, expands, and pops the outer brick face off: that flaking is freeze-thaw spalling, and in Arlington it's accelerated because our brick takes on water in fall, then meets a sudden January freeze. The fix is sequence-sensitive — waterproof and seal the crown in fall, before the freeze, not after the damage. A breathable repellent that sheds liquid water while letting vapor escape is the premium treatment; a film-forming sealer traps moisture and makes it worse.

03

Hail

DFW sits in the most hail-battered corridor in the country. After spring storm season we check crowns, chase covers, and caps for impact — a dented chase cover that now ponds water instead of shedding it is a leak waiting for the next freeze. Storm damage is also a legitimate NFPA 211 "significant weather event" trigger for a Level 2 scan, and a photographed report is what holds up on an insurance claim.

04

When to book

Schedule masonry repair and crown sealing for September–October: repointing and crown coatings must cure above freezing and be in place before the first burn. Waiting until you smell smoke or see a ceiling stain means doing the work in the worst possible conditions — the expensive version of a cheap fall fix.

Code note · the DFW Metroplex

North-Texas code reality: the 3-2-10 chimney-height rule governs termination, and masonry repointing and crown coatings must cure above freezing — so the inspection and any sealing belong in the September–October window, before the first burn.

Built to code · Electric Fireplace Installation in Arlington

Electric Fireplace Installation is held to published national standards no matter the city. Our Arlington crew builds to these and documents the work; the locally-adopted code edition and permit requirements are confirmed with Tarrant County's authority on every job.

  • Listed appliance, installed to its listing (UL 2021) UL 2021 is the standard electric fireplaces are evaluated to as fixed and insert heaters, and our installs stay strictly inside the unit's listing and manufacturer instructions. Rough-opening size, intake and exhaust clearances, recess depth: each figure comes from that listing, never from a guess.
  • Dedicated branch circuit (IRC / NEC) Following general NEC continuous-load practice, a heater-rated unit drawing more than 50% of a 15- or 20-amp circuit gets its own dedicated branch circuit, keeping it off shared outlets that would trip or overheat.
  • Clearance to combustibles Above and beside the unit, mantel, trim, and framing hold to the manufacturer's listed minimum clearances, and any built-in recess is framed so heater air can escape rather than sit trapped against combustible studs.

Scoped from a graded inspection

At Space Fireplace Services, a electric fireplace installation is never guesswork. We scope every job from a graded, photographed inspection first — the NFPA 211 level the evidence calls for — so the work is matched to what your flue and masonry actually need, with the report to prove it. The documented inspection is the record the electric fireplace installation is built on.

Chimney inspection in Arlington
What's included

Every electric fireplace installation in Arlington

Deliverables

  • Full sweep + inspection
  • Soot containment + HEPA vacuum
  • Level 1 visual inspection report
  • Photos of any code issues
  • Recommendations + written quote
  • Drop cloths + clean cleanup

How a job runs

01

Plan

We select the unit and confirm the panel can carry a dedicated circuit for it.

02

Frame

The squared recess gets framed to the unit's own dimensions and clearances.

03

Power

We run the dedicated circuit or set the rated receptacle or whip it calls for.

04

Set & commission

We set it dead level, tighten the reveal to the finish, then run the heater and flame with you watching.

Coverage

7+ neighborhoods in Arlington

Same-week service across every neighborhood in Arlington. Don't see yours? Call (469) 992-4912 — if it's in Arlington, we cover it.

Pantego
Dalworthington Gardens
Viridian
Lake Arlington
South Arlington
North Arlington
Entertainment District
Local crew

The Arlington advantage.

Our Arlington crew lives in the metro they serve, across Tarrant County. They know which Arlington neighborhoods — Pantego, Dalworthington Gardens, Viridian and more — have crumbling crowns, and which newer builds skipped the cap. Local code knowledge, local referrals, local accountability for every electric fireplace installation.

CSIA-certified inspectors
Same-week scheduling in Arlington
1-year workmanship warranty
399k
Arlington residents
17
ZIP codes
7+
Neighborhoods
< 2 min
Human reply · 7 AM – 12 AM
Questions, answered

Electric Fireplace Installation in Arlington — FAQ

Does a new install call for a dedicated circuit, and do I need an electrician for that?

It depends on the model you fall for. Plug-in units are happy on a standard 120 V outlet, while heater-rated inserts and built-ins typically draw enough current to need their own dedicated branch circuit, keeping breakers from tripping and shared wiring from overloading. Panel capacity gets assessed at the start, so you know up front whether running a dedicated circuit is part of your install.

How much time does it take to install a new electric fireplace start to finish?

For a wall-mount or insert landing on existing power, count on a few hours. The timeline stretches when the design calls for more: framing a recess into the wall, pulling a new dedicated circuit, or the finish and trim work that makes the unit read built-in. All of that belongs to the install itself; a later repair visit never touches it.

What falls under the installation price, and which items are billed on top?

Framing or fitting the opening, mounting, making the electrical connection, and commissioning all sit inside the starting price. What moves the final number is the unit type, whether the design calls for recessing or a new circuit, and how the wall gets finished. Note that the fireplace unit itself is usually priced apart from the install labor.

Will a new electric insert fit into the masonry fireplace I already have?

Very often, yes. Slipping an electric insert into an unused wood-burning firebox is among the cleanest ways to bring that opening back to life, since it needs no venting and no gas. Before recommending a specific model, we measure the firebox opening and confirm a safe power source can reach it, so the insert you choose fits properly and trims out clean.

Once I go electric, should the chimney be capped or sealed off?

It earns its keep. Once the burning stops, an open flue goes right on pulling cold air, drafts, and moisture into your living space. That is why many homeowners going electric add a top-sealing damper or cap, or block the flue outright, and reclaim the energy that open chimney had been quietly draining.

My 1980s Arlington fireplace has the brass-and-glass doors. Can it be modernized without demolition?

Yes, and demolition is usually the wrong tool anyway. We set a sealed gas insert inside the existing opening, run a new stainless liner up the old chimney, and build the new surround right over the brick. The dated box becomes a shell nobody sees. Most of these remodels take days, not weeks, and the room keeps its bones.

Can you convert a wood-burning fireplace to gas in Arlington?

Yes — the real choice is between vented gas logs, which keep the open-fire look but send most heat up the flue, and a sealed insert, which actually heats the room. Either way Arlington requires a permit for the gas line, a licensed plumber runs it, and we draft-test the chimney before handoff. You get photos of all of it.

What should I look at in the showroom before a re-face?

Scale and flame, mostly. A 36-inch flame reads completely differently against a 14-foot brick wall than in a showroom bay, so bring photos and wall dimensions. Seeing burn media in person — logs, stones, glass — settles arguments a screen can't. An hour in front of burning units usually saves two rounds of second-guessing later.

Do you serve all of Arlington?

Yes — our crews cover Arlington's 17 ZIP codes across Tarrant County, including Pantego, Dalworthington Gardens, Viridian, plus the surrounding communities.

How soon can you schedule electric fireplace installation in Arlington?

We offer same-week scheduling across Arlington, booked by a real person in under two minutes, 7 AM to midnight every day.

Why do Arlington homes need electric fireplace installation?

Arlington's mid-century brick ranches and the newer Viridian master-planned community sit squarely between Dallas and Fort Worth. Freeze-thaw crown cracking on the older stock and prefab cap work on the newer builds are the year-round staples. From feature wall to firebox, we keep the hearth the standout it was built to be. Electric Fireplace Installation is part of keeping that local housing stock safe, efficient, and up to code.

How much does electric fireplace installation cost in Arlington, TX?

Electric Fireplace Installation in Arlington starts from $725, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (469) 992-4912 for a free, no-pressure Arlington quote.

Do you offer emergency or same-day electric fireplace installation in Arlington?

Yes — we run same-week and emergency electric fireplace installation across Arlington, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (469) 992-4912 and we prioritize Arlington dispatch so a craftsman is on it fast.

Is there a CSIA-certified electric fireplace installation company near me in Arlington?

Our Arlington crew lives in and works the metro across Tarrant County, including Pantego, Dalworthington Gardens, Viridian — a certified, local electric fireplace installation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (469) 992-4912.

Last reviewed:

10+
Years
NFPA 211
Compliant
CSIA
Certified
< 2hr
Response
Ready when you are

Talk to a CSIA-certified expert today.

Free written quote. Same-week scheduling. 24/7 emergency response when you need it.

Licensed & Insured Same-Week Scheduling Written Quote, Always
Emergency

24/7 Response

Active leak, animal in flue, post-fire damage, or smoke event? Real humans on the line 7 AM to 12 AM every day — replies in under 2 minutes. Tech dispatch within 2 hours during business hours, subject to crew availability after-hours.

Emergency line
Call NowBook