Spark Arrestor Installation in Alamo Heights, TX

A spark arrestor is the mesh screen that keeps burning embers in, so they cannot escape the flue and light up the roof or the brush. A cap is the lid that keeps rain and animals out. One guards the outside world from the fire within; the other guards the flue from the weather without. They are often built into a single fitting, which is why the two get confused, but the arrestor is specifically the code-sized screen, and we will fit one to a cap you already own.

No screen over the flue at all, even where a weather cap is in place; embers or sparks you can see leaving the chimney top; or an existing arrestor rusted through, torn, or sooted solid. A local burn code or an insurer in a fire-prone area may also demand one. Homes near trees, dry brush, or wildfire country, and anyone burning wood, gain the most from a working screen on every flue.

NFPA 211 sets it: the screen has to be corrosion-resistant material with openings no smaller than 3/8 inch and no larger than 1/2 inch. That 3/8-inch minimum keeps the screen from sooting shut and strangling the draft; the 1/2-inch maximum is what stops embers from slipping out. Those two limits are what make an arrestor an engineered fire part instead of a cap collar. Some wildfire jurisdictions run tighter, and where the local rule is stricter it wins.

Almost certainly, and frequently to a stricter standard than the NFPA baseline. In a designated fire-hazard or wildland-urban-interface area, one escaped ember is a real wildfire risk, so local code and plenty of insurers require a compliant arrestor on every solid-fuel flue. We confirm the local mesh-and-material rule, install to it, and document the screen size for your inspection or insurance file.

Burning embers can leave the flue and settle on the roof or in the brush around it, and over a combustible roof or near dry vegetation that is a roof-fire or wildland-fire waiting to start. An inexpensive screen heads off an expensive fire. If your top is also open with no cap, you are letting in the rain and animals a cap would keep out, which is exactly why the two so often go on together.

Bolt-on and clamp-on screens and arrestor-caps are out there, but the work happens at the flue top on the roof, the mesh has to land inside the code size range, and the screen has to seat to the tile or pipe and hold in wind. A loose or wrong-mesh screen fails at the one thing it is there to do, containing embers, so both the fit and the mesh size need verifying against the code that applies where you live.

Usually, yes — the firebox is rarely the problem. The flue is. Most pre-war chimneys here are unlined or clay-lined with open joints, and gas exhaust is wet, so we reline with a properly sized stainless liner, set a damper clamp, and test draft before the logs go in. The original surround and mantel stay untouched.

Depends what's under the paint. If the brick or period tile is intact, restoration usually wins — that detail is part of what these houses are worth. If a previous owner already chiseled it flat, a limestone or plaster re-face in period proportions is the honest path. We'll tell you which house you have before you commit money.

Yes. Alamo Heights is its own city with its own permit office, and gas line work there needs a licensed plumber and an inspection like anywhere in Texas. We pull the permit, schedule the inspection, and close with a photo report showing the liner, clearances, and test results — the boring paperwork that matters when you sell.

Yes — our crews cover Alamo Heights's 1 ZIP code across Bexar County, including Olmos Park line, Terrell Hills, Lower Alamo Heights, plus the surrounding communities.

We offer same-week scheduling across Alamo Heights, booked by a real person in under two minutes, 7 AM to midnight every day.

Alamo Heights is San Antonio's historic affluent enclave — 1920s-40s Spanish-revival and brick mansions near Olmos Park. The work here is period-correct masonry repointing, clay-liner relining, and crown rebuilds on chimneys approaching a century old. The fireplace anchors the room here, and we keep it that way — sound beneath, sharp on the surface. Spark Arrestor Installation is part of keeping that local housing stock safe, efficient, and up to code.

Spark Arrestor Installation in Alamo Heights starts from $275, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (469) 992-4912 for a free, no-pressure Alamo Heights quote.

Yes — we run same-week and emergency spark arrestor installation across Alamo Heights, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (469) 992-4912 and we prioritize Alamo Heights dispatch so a craftsman is on it fast.

Our Alamo Heights crew lives in and works the metro across Bexar County, including Olmos Park line, Terrell Hills, Lower Alamo Heights — a certified, local spark arrestor installation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (469) 992-4912.