Blown-In Insulation in Houston, TX

Cellulose runs about R-3.7 per inch and fiberglass about R-2.5 per inch, so hitting the same R-value target takes noticeably more inches of fiberglass than cellulose. Cellulose packs denser and resists air drifting through the blanket better, but it's heavier and settles more; loose-fill fiberglass is lighter, barely settles, and won't wick water if the attic leaks. We read each material's coverage chart and blow it to its own correct install depth, because inch-for-inch they are not interchangeable.

Because it settles after install, cellulose more than fiberglass, the depth on day one isn't the depth six weeks later. We install above the final R-target so that once the blanket settles, the SETTLED depth still meets spec. Blowing only to the target on day one leaves you short after settling, and that's one of the most common ways a loose-fill job quietly under-delivers.

No, and that's the key limit of the method. Loose fill is a conductive barrier, slowing heat as it moves through, but air still leaks straight past it at top-plate gaps, can lights, and penetrations. Blown over an unsealed attic it merely filters the leaking air. Air-sealing is a separate step that should come first; the blow handles conduction, not leakage.

Usually yes, as a top-off, as long as the existing layer is dry, intact, and neither moldy nor matted. Loose fill drapes right over old fill, and we blow the added depth to bring the total up to target. If the old layer is settled flat or crushed by foot traffic, we re-fluff or re-level it first, so the new fill isn't just resting on a dead, compressed base.

Loose fill's whole advantage is a seamless blanket that conforms around joists and wiring with no gaps, but only when it's installed to an even depth at the right machine density. Under-fluffed or thin-at-the-edges fill leaves cold spots. We dam the eaves, dial in the blower density, and staple depth-marker rulers across the deck, so the installed inches are a measurement you can read rather than a number we promise.

If you're buying it for heating economics, no — thirty nights a year pays nothing back, and we'd rather say that up front. People here buy fireplaces the way they buy good lighting: for what the room feels like at 8 p.m. If that's the goal, it's worth doing properly — right scale, right flame, right surround — or not at all.

Direct-vent gas, almost certainly. The sealed vent runs horizontally through an exterior wall or up a short chase, so no masonry and no full-height chimney. Linear or traditional format both work; the constraints are exterior wall access, termination clearances from windows and property lines, and gas supply sizing up three floors. We map all three before you pick a unit.

That's the standard Heights job. The original opening and mantel stay; a stainless liner drops down the existing flue; a vented log set sized to the small pre-war firebox goes in. Done right, the only visible change is that the fire lights with a switch. Done wrong — oversized logs crammed into a shallow box — it reads fake immediately. Sizing is everything.

Yes — our crews cover Houston's 180 ZIP codes across Harris County, including The Heights, River Oaks, Montrose, plus the surrounding communities.

We offer same-week scheduling across Houston, booked by a real person in under two minutes, 7 AM to midnight every day.

Houston spans century-old masonry in The Heights and River Oaks to sprawling prefab-firebox new-build across its suburbs. The humid Gulf climate means the dominant work is animal and nest removal, chase-cover and cap corrosion, and moisture intrusion — not the freeze-thaw of colder metros. Each home's fireplace is the heart of its main room, and our service is built around protecting that centerpiece. Blown-In Insulation is part of keeping that local housing stock safe, efficient, and up to code.

Blown-In Insulation in Houston starts from $1,600, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (469) 992-4912 for a free, no-pressure Houston quote.

Yes — we run same-week and emergency blown-in insulation across Houston, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (469) 992-4912 and we prioritize Houston dispatch so a craftsman is on it fast.

Our Houston crew lives in and works the metro across Harris County, including The Heights, River Oaks, Montrose — a certified, local blown-in insulation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (469) 992-4912.