Blown-In Insulation in Alamo Heights, TX

Cellulose runs about R-3.7 per inch and fiberglass about R-2.5 per inch, so hitting the same R-value target takes noticeably more inches of fiberglass than cellulose. Cellulose packs denser and resists air drifting through the blanket better, but it's heavier and settles more; loose-fill fiberglass is lighter, barely settles, and won't wick water if the attic leaks. We read each material's coverage chart and blow it to its own correct install depth, because inch-for-inch they are not interchangeable.

Because it settles after install, cellulose more than fiberglass, the depth on day one isn't the depth six weeks later. We install above the final R-target so that once the blanket settles, the SETTLED depth still meets spec. Blowing only to the target on day one leaves you short after settling, and that's one of the most common ways a loose-fill job quietly under-delivers.

No, and that's the key limit of the method. Loose fill is a conductive barrier, slowing heat as it moves through, but air still leaks straight past it at top-plate gaps, can lights, and penetrations. Blown over an unsealed attic it merely filters the leaking air. Air-sealing is a separate step that should come first; the blow handles conduction, not leakage.

Usually yes, as a top-off, as long as the existing layer is dry, intact, and neither moldy nor matted. Loose fill drapes right over old fill, and we blow the added depth to bring the total up to target. If the old layer is settled flat or crushed by foot traffic, we re-fluff or re-level it first, so the new fill isn't just resting on a dead, compressed base.

Loose fill's whole advantage is a seamless blanket that conforms around joists and wiring with no gaps, but only when it's installed to an even depth at the right machine density. Under-fluffed or thin-at-the-edges fill leaves cold spots. We dam the eaves, dial in the blower density, and staple depth-marker rulers across the deck, so the installed inches are a measurement you can read rather than a number we promise.

Usually, yes — the firebox is rarely the problem. The flue is. Most pre-war chimneys here are unlined or clay-lined with open joints, and gas exhaust is wet, so we reline with a properly sized stainless liner, set a damper clamp, and test draft before the logs go in. The original surround and mantel stay untouched.

Depends what's under the paint. If the brick or period tile is intact, restoration usually wins — that detail is part of what these houses are worth. If a previous owner already chiseled it flat, a limestone or plaster re-face in period proportions is the honest path. We'll tell you which house you have before you commit money.

Yes. Alamo Heights is its own city with its own permit office, and gas line work there needs a licensed plumber and an inspection like anywhere in Texas. We pull the permit, schedule the inspection, and close with a photo report showing the liner, clearances, and test results — the boring paperwork that matters when you sell.

Yes — our crews cover Alamo Heights's 1 ZIP code across Bexar County, including Olmos Park line, Terrell Hills, Lower Alamo Heights, plus the surrounding communities.

We offer same-week scheduling across Alamo Heights, booked by a real person in under two minutes, 7 AM to midnight every day.

Alamo Heights is San Antonio's historic affluent enclave — 1920s-40s Spanish-revival and brick mansions near Olmos Park. The work here is period-correct masonry repointing, clay-liner relining, and crown rebuilds on chimneys approaching a century old. The fireplace anchors the room here, and we keep it that way — sound beneath, sharp on the surface. Blown-In Insulation is part of keeping that local housing stock safe, efficient, and up to code.

Blown-In Insulation in Alamo Heights starts from $1,800, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (469) 992-4912 for a free, no-pressure Alamo Heights quote.

Yes — we run same-week and emergency blown-in insulation across Alamo Heights, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (469) 992-4912 and we prioritize Alamo Heights dispatch so a craftsman is on it fast.

Our Alamo Heights crew lives in and works the metro across Bexar County, including Olmos Park line, Terrell Hills, Lower Alamo Heights — a certified, local blown-in insulation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (469) 992-4912.